Login Status  Login Status

Not logged in

» Login
0 Product(s) in cart
Total $0.00
Online Payment Service

Home » All Products

 Checkout
PriceKeyword
Cables for Brusa
Cables for Brusa NLG513

We located a few Azure Dynamics eTransit Connect wiring harnesses for the Brusa NLG513 charger.  This consists of a battery cable with 5pin connector to connect to the traction battery pack, and a mains cable with SAE J1772-2010 charge port.  These are high quality cables built for the eTransit Connect Vehicle.

The Brusa NLG513 ships with the connector parts you need to make up such cables.  These are assembled cables.

Price: $299.00
Volt/Amp/kWh Coulometer
Previous1 of 4Next

MYPIN Coulometer


This meter is a little larger than our JLD404.  It displays Kilowatt Hours kWh, Voltage, and Current simultaneously with large red easy to read numerals.

While AmpHours are a pretty good measure of used pack energy, kWh are actually slightly better.  They are a function of both voltage AND current so as your pack voltage changes, your amp-hour rate will as well.  But kWh measure both voltage and current for a slightly more accurate measure of power.

Additinoally, this meter lets you monitor voltage, current, AND kilowatt hours simultaneously.

:
Price: $299.00
Azure Dynamics Axiomatic Wake-On-Charge Module
Previous1 of 2Next
 P/N105200 +A Azure Dynamics Wake On CHarge module used on the Ford eTransit Connect.

High failure item preventing the battery from charging.
Price: $295.00



GENUSUN WATERPROOF 105-350W 56.8V LITHIUM BATTERY SOLAR CHARGE CONTROLLER
Previous1 of 2Next
Marine Grade.  This is a very unusual charge controller in that it can charge a battery of a HIGHER voltage than the solar panel output that feeds it.  In this way, you can charge a nominal 48v lithium  battery pack to a precise 56.8v using a solar panel that puts out 33v at its maximum power point.  This is the only device we've found that will do that.

We had these specially made by Genusun in their waterproof casing - fully potted and in a plastic enclosure.  This will last forever in marine/boat applications as well as golf cart canopies or other outdoor in the weather applications.

This one is designed to charge 16 LiFePo4 cells to 56.8v using a Constant Current/Constant Voltage charge curve perfect for our LiFePo4 cells.  

But it can do it from ANY of our flexible solar panels - a single panel. 

Why?  Put a single panel on the roof of your golf cart or the deck of your john boat and use this to charge a 48v battery pack at up to 8 amps.  It could not be simpler.  We haven't seen anything else out there like this "boost" charge controller device.
Price: $295.00
J1772 Charge Cable 40A
Make your own Electric Vehicle Charge Station.  This connector with 25 foot of 40A cable is not to be confused with the little units from China.  Made by Leviton, this is heavy duty and the real thing.

This UL Rated, J1772 Level 2 Charge Connector will accommodate up to 40A, 208V - 240V AC systems, and has the ability to connect with any J1772TM compliant Electric Vehicle.

The handle is ergonomically designed to fit comfortably in the hands of any EV driver, yet robust enough to be rated at 10,000 cycles - the equivalent of 27 years of use! Features and Benefits: *Compatible with all Charging Station Standards and Recommended Practices, including SAE J1772

*Guaranteed 10,000 mating cycles - equivalent to 27 years of use! *

Drain holes prevent water from pooling inside of the connector housing, preventing against ice build-up and stagnant water accumulation.

*Ergonomically designed handle for a comfortable grip in any EV driver's hands

*Low contact resistance

*25 ft. long EV charging cable

*Cord Type EVJE - 3 X 10AWG & 2 X 16 AWG conductors  
Price: $295.00
1 Rebling7002 Battery Receptacle and Mating T Handle Connector
Previous1 of 7Next
 Rebling 7002 standard duty 250F green receptacle and gasket is the female battery connector for your next battery box.  Carries 750 amps of continous current or up to 1500 amperes peak.  The Rebling 7016-1 T-handle plug is ideal for cable terminals up to 3/0.

Rebling plastics has developed a line of high quality high current milspec battery connectors used primarily in aviation applications.  Pricey, but extremely safe and extremely durable, these will last in electric vehicles for years providing a very low resistance high current connection with the convenience of a half-turn handle to disconnect the pack.

Price: $295.00



Tesla Model S and Model X CAN Monitor
Previous1 of 4Next
SavvyCAN for Tesla Model S

SavvyCAN for Tesla Model S is a Controller Area Network Capture device capable of capturing CAN data directly from the Tesla Model S diagnostics connector even at the very high data rates found on the Tesla Model S.

The system consists of a data capture and analysis program for your Windows, Linux, or Mac OSX Laptop that connects to the EVTV CAN Microcontroller device by USB cable.  The CANDue features a wiring harness with the appropriate connector to connect right to the diagnostics connector below the 17 inch display on the center console of the Tesla Model S to access CAN3 - The Drive Train CAN Bus on the ModelS


:
Price: $295.00
4 inch Flywheel Coupler Blank
Previous1 of 3Next
Couplers fit any standardized 24 spline motor including TM4, Siemens, UQM & Remy. These are very snug fit couplers to fit over the splined shaft of motors such as the Siemens and UQM. You must heat them to about 300F to install them over the splined shaft. When cool, they will have a very tight fit. They are also blank. This is so you can machine them further to fit specific flywheels and horizontal distances from motor face. So additional machining will normally be required. These couplers represent the hard part - Electric Discharge Machining to produce the involute spline for the motor shaft. These blanks are then further machined to fit flywheels normally.
Price: $293.00
Billet J1772 Charge Port Kit for Electric Vehicles
Previous1 of 4Next
Solid 6061 billet aluminum SAE-J1772-2010 Charge Port for your electric vehicle WITH the AVC2 circuit to respond to control pilot signals and proximity switch.

This device includes a relay you can use to disable your controller or perform other actions (turn on dash indicator?) whenever your car is connected to J1772 EVSE.

Complete instructions for adding J1772 charge capability to any electric vehicle.

Billet aluminum connector lasts forever and looks great on your vehilcle. Everyone wants to see "where you plug it in." Make yours look truly professional.

Make use of thousands of J1772 charge stations across the country.

Price: $279.00



PTC Space Heater
Previous1 of 3Next
PTC HEATER for Electric Cars.

This is a PTC space heater for use in an electric car.  It operates nominally at 110v but we've run these as high as 200v in the past with great success and down to about 90v pack voltage.  It is also available in 220v and  360v versions.

Postive Temperature Coeffeicent heaters are very safe.  As temperature rises, so does resistance and so the current decreases.
:
Price: $279.00
3 inch Flywheel Coupler Blank
Previous1 of 3Next
Couplers fit any standardized 24 spline motor including TM4, Siemens, UQM & Remy. These are very snug fit couplers to fit over the splined shaft of motors such as the Siemens and UQM. You must heat them to about 300F to install them over the splined shaft. When cool, they will have a very tight fit. They are also blank. This is so you can machine them further to fit specific flywheels and horizontal distances from motor face. So additional machining will normally be required. These couplers represent the hard part - Electric Discharge Machining to produce the involute spline for the motor shaft. These blanks are then further machined to fit flywheels normally.
Price: $258.00
Flexible Solar Panel 120w
Previous1 of 3Next
A 120 WATT SOLAR PANEL UNLIKE ANY YOU'VE SEEN

This lightweight, high efficiency solar panel is unusually well suited to electric boats, aircraft, RVs and  electric vehicles.  Here's why:  

LIGHT WEIGHT at just 2.45 kilograms - 5.4 pounds each.

VERY THIN - just 3 mm (0.118 inches) thick and built on a very durable flexible acrylic sheet.  This means you can mount it on curved surfaces with minimal wind resistance.  About 30% deflection is possible.

VERY HIGH EFFICIENCY -  20-23%.  This panel is made for EVTV in China using a special laminate. But the individual cells are made in the U.S. by SUNPOWER using their MAXEON back connect technology for efficiencies up to 24%.

What this means is that you can put solar panels in places impractical before.  The lightweight, thin, flexible panels can be attached to RV roofs, boat decks, canopies, and places where the usual 45 lb stiff framed glass panels would simply be absurd.

And since real estate on these "vehicle" applications is limited, paying for the extra efficiency of these superior cells actually makes sens
e.



Price: $245.00

« | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10... | »