Login Status  Login Status

Not logged in

» Login
0 Product(s) in cart
Total $0.00
Online Payment Service

Home » All Products

 Checkout
SearchPriceKeyword
Four Module Harness for Tesla Battery Modules
1 of 2
 This is a wiring harness that plugs into the BMS board connectors on the Tesla Battery Module.  This harness will connect four Tesla battery modules.
Price: $59.95
Add to cart
Tesla Battery Module Shorting Plug
 This shorting plug allows you to use an ODD number of Tesla Battery Modules, 1, 3, 5, 7, etc.
Simply plug this into the LAST position of a two plug or 4 plug harness (not the extension harness) and you can have an odd number of Tesla Battery Modules in your project
Price: $23.95
Add to cart
Stacking Strap for Tesla Battery Modules
1 of 2
 These heavy copper 1 inch straps feature heavy MILSPEC shrink wrap insulation and are perfect for connecting two Tesla Battery Modules stacked vertically.
Price: $21.95
Add to cart



Braided Battery Strap Kit for Tesla Battery Modules
As it so happens, our own 70mm battery straps are the PERFECT length to strap two Tesla Battery Modules together side-by-side.
Price: $9.00
Add to cart
1 CANKIT - CANbus kit with Microcontroller and Cable
1 of 7
The EVTV CAN KIT contains a generic multicontroller clone of the popular Arduino Due board, a dual channel CAN bus shield with microSD card slot and EEPROM and a USB Cable.

Arduino has released a new 32-bit ARM based version of their popular multicontroller they call the Arduino Due. It actually has TWO Controller Area Network (CAN) controllers built into it - but no transcievers   In a stunning second omission, Arduino Due provides NO EEPROM for persistent memory.  You can't save variables from one power up to another.

 Ergo the EVTV CANDue 2.2 Dual Channel CAN bus Shield for Arduino Due.  This card features  TWO CAN channels along with the transcievers to enable them - tied to the CAN controller pins on the Due.  It also features a Single Wire CAN Chip and connections.

We also included a 2Megabit EEPROM chip - 256Kbytes of storage for persistent variables or pixel data.

And finally, we included a microSD card slot to hold up to 128GB of removable memory for logging data.

Convenient screw terminals allow connections to the vehicle 12v and chassis ground to power the entire rig of multicontroller and CAN bus board.  It also can read and write CAN messages to your vehicle OBDII CAN bus.

We also include the generic multicontroller board itself - a clone of the Arduino Due board.
Price: $149.00
Add to cart
Danfoss DLX 4.4 Grid Tied Inverter
1 of 2
 Danfoss DLX4.4 Grid-Tie Inverter.  This device puts out up to 4.4kW of 240vac 60Hz electrical power from a 230-500v DC input.  It is UL1741 compliant and must have an existing AC waveform from an off-grid inverter or utility-grid to synchronize to.

This is ideal for using full Tesla Model S battery packs at the nominal 345 voltage for peak shavers or time of day rate shifters.
Price: $595.00
Add to cart



Explosion Proof 20kw Off-Grid Inverter
1 of 2
 This 20kw True Sine Wave off-grid inverter features a very rugged explosion proof enclosure which was designed for use in mines. But the result is it is extremely resistant to weather..  It has been modified to take our frequency shift input to shift the frequency between 60.0 and 62.5 Hz to shut off grid interactive inverters when the battery reaches 100% state of charge. 

It also works perfectly with our Tesla Model 3 battery and controller with a 300-400vdc input and a 240VAC split phase output L1, L2, and N common in the United States.  Simply wire into your loads panel with a 100Amp circuit breaker and turn off the grid.


Price: $19,995.00
Add to cart
Gigavac GX16BEB 600 Amp 800v Contactor
1 of 4
600 AMPERE 800V CONTACTOR WITH AUXILIARY CONTACTS FEATURES
  • Chassis level power terminals – No need for specially routed power cables, special bus bars, or special lugs.
  • Rugged EPIC® seal rated to 175°C – Reduced risk of re or meltdown in over current conditions. The same technology used for advanced aerospace programs.
  • Hermetically sealed – Designed to meet: UL1604 for Class I & II, Div 2 and Class III for use in hazardous locations,
  • IP67 for temporary water immersion for 30 min, SAE J1171 - external ignition protection, and ISO8846 for protection against ignition around ammable gasses.
  • High Ef ciency Dual DC Coils – Very low 12, 24 or 48 VDC continuous coil power with no EMI emissions or cross- talk on your system control power. Ideal for battery powered systems or where low power is needed.
  • Built-in coil suppression for all DC coils – Saves you engineering time and parts cost to add external coil suppression.
  • Stainless steel nuts, washers and mounting inserts, for years of corrosion free service.
  • Not position sensitive – can be mounted in any position for ease of installation.
Price: $299.00
Add to cart
Gigavac GX14BA Epic 350 Amp Contactor
1 of 6

The GIGAVAC GX14BA contactor is a 350 ampere single-pole single-throw (SPST) normally open (NO) high voltage high current relay capable of breaking current flows up to 900 volts.. 

Mechanically rated for over 1,000,000 cycles, this hermetically sealed contactor features built-in coil suppression and IP67 environmental rating.

The coil operates on 8-16vdc with a 4.3 amp close but a small 240 ma holding current.

UL 1604 listed for Classes I, II, and III.

Price: $149.00
Add to cart



Gigavac  Epic 350 Amp  Contactor w/aux contacts
1 of 7
The GIGAVAC GXL14B1BAB contactor is a 350 ampere single-pole single-throw (SPST) normally open (NO) high voltage high current relay capable of breaking current flows up to 800 volts.. 

Mechanically rated for over 1,000,000 cycles, this hermetically sealed contactor features built-in coil suppression and IP67 environmental rating.

The coil operates on 8-16vdc with a 4.3 amp close but a small 240 ma holding current.

UL 1604 listed for Classes I, II, and III.

This version features a set of auxilary contacts allowing you to detect contact closure or opening programatically.  This is useful to detect welded contacts.
Price: $240.00
Add to cart
120W 48v LED Solar Tower Light
1 of 6
Another Bargain for you from the DC Solar Auction. These 48v 120watt CREE LED Lights list for nearly $300, and we have them at a third of the price. DC Solar just closed the largest bankruptcy of a Solar Company in history with over $50 million in parts. We picked up a few pallets of these SparksPower. Ggrab em while you can.  When they are gone they are gone.
List Price: $299.95
Price: $99.95
Add to cart
1 Rebling7002 Battery Receptacle and Mating T Handle Connector
1 of 9
 Rebling 7002 standard duty 250F green receptacle and gasket is the female battery connector for your next battery box.  Carries 750 amps of continous current or up to 1500 amperes peak.  The Rebling 7016-1 T-handle plug is ideal for cable terminals up to 3/0.

Rebling plastics has developed a line of high quality high current milspec battery connectors used primarily in aviation applications.  Pricey, but extremely safe and extremely durable, these will last in electric vehicles for years providing a very low resistance high current connection with the convenience of a half-turn handle to disconnect the pack.

Price: $295.00
Add to cart

« | ...10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 | 20... | »