Login Status  Login Status

Not logged in

» Login
0 Product(s) in cart
Total $0.00
Online Payment Service

Home » Battery Connections

 Checkout
PriceKeyword
Tinned Copper Terminal 2/0 5/16 90 degree
1 of 2
 Tinned Copper Terminal for 2/0 cable.  Connector hole 5/16 inch.  90 Degree bend
Price: $4.95
Add to cart
4 AWG Extra Flexible Cable
This braided 4 AWG cable is unshielded but extra flexible and because its welding cable it can handle up to 600 volts. 
Price: $6.25
Add to cart
Anderson SB50 Two Pack
1 of 2
2 Pack, 2 Complete Connectors Anderson SB50 Connector Kit Gray 6319G1 50 Amp Rating AC/DC Gray housing, 10/12 AWG Maximum Wire Anderson Connectors are designed to plug into each other. They are not Male/Female
Price: $12.95
Add to cart



12v Battery Disconnect
1 of 2
ProMax 12-Volt Heavy Duty PriorityStart! Automobile Battery Protector / Electronic Cut Off Switch

Heavy Duty Battery Disconnect Switch
-- Maintenance Free & Ecologically Friendly
 -- Totally Automatic Computerized Voltage Disconnect System
 -- Automatic Battery Reconnect that's Convenient & Safe
-- Easy to Attach in just 3 Simple Connections
-- Maximizes Battery Life, Preventing Electrical Damage
-- Disconnect Threshold is Factory Set at 11.7V for 12V Systems
-- Handles 1,000 Starting Amps
-- Designed for an Under-Hood Environment
-- Engine Run & Hazard Light Protection
 -- Universal Design fits both Top & Side-Post Batteries
 -- For Surge Protection / Fully Automatic Engine Starting Protection for your Car, Boat, or other Vehicle
-- Operates only when Accidental Deep Discharge of Vehicle [Auto] or Marine Batteries are Taking Place
-- To Operate Headlight Switch, Step on Brake Pedal, or any other Electrical Accessory, and it will Automatically Reconnect
-- Unit can only be used with Class 1 - 6 Vehicles with a Maximum of 1,000 Peak Starting Amps (Rated at 250 Continuous Amps)
-- Monitors Battery Voltage & Automatically Disconnects any Undesired Drain on your Battery as the Voltage Reduces (when Engine is not running)

How It Works: . PriorityStart! is an automatic heavy duty computerized on/off switching system, protecting battery voltage and starting power. If battery voltage drains below 11.7 volts when engine is off, it automatically disconnects the load. The battery voltage immediately recovers. . TO START: Just step on the brake pedal, and the starting power is automatically reconnected. It is designed to handle 1,000 Starting Amps. (PriorityStart! is not a battery charger or booster that is used after the battery has already been damaged.) Installation: .

PriorityStart! attaches easily to any 12 Volt top or side-post vehicle battery. No modifications are necessary. Three Easy Connections: 1. Connect existing vehicle positive cable to PriorityStart! 2. Connect PriorityStart! cable to battery positive post. 3. Attach ground wire to battery negative post. . 
Price: $189.00
Add to cart
Battery Feeder Stud - Black
Bring your DC through bulkheads or firewalls with a Black battery feeder stud or "passthrough", these are generally used in tighter areas where a gland nut won't fit ,you need to make an immediate turn in your wiring or a removable section. Features 3/8" brass studs and heavy duty plastic insulator and mounting bushing.
Price: $14.95
Battery Feeder Stud - Red
Bring your DC through bulkheads or firewalls with a Red battery feeder stud or "passthrough", these are generally used in tighter areas where a gland nut won't fit ,you need to make an immediate turn in your wiring or a removable section. Features 3/8" brass studs and heavy duty plastic insulator and mounting bushing.
Price: $14.95



1 Rebling BFS131 Master Disconnect Switch
1 of 3
 Rebling BFS-131 Master Disconnect High Voltage Interlock Switch is our most powerful switch capable of 600 continuous amps and up to 3000 amperes peak at voltages up to 2500v.

This switch features an OSHA lockout/tagout and an auxilliary microswitch to simultaneously disconnect contactors.  Environmentally sealed to IP67.  Designed specifically for electric vehicles, this is the 800lb gorilla of maintenance switches.
Price: $195.00
Add to cart
Braided Battery Strap Kit - 60 mm centers
We have found these braided straps to be the best connection you can have for your Lithium battery pack. They provide a large surface area to carry high levels of current. These straps allow for some flex between the batteries which reduces the stress on the terminals themselves. The straps are sold as individual pieces and include two M8 bolts and two Nord-Lock washers as mounting hardware.
Price: $9.00
Add to cart
Braided Battery Strap Kit 30mm Centers
 Braided tinned copper battery strap 30 mm from center hole to center hole AND 30mm2 cross sectional area. 

These straps feature 6 mm hole width for M6 terminal bolt and are designed specifically the CAM72CI battery.

Includes strap, two M6 stainless hex head cap screws and two M6 Nord-Lock Zinc Flake washers.
Price: $9.00



Braided Battery Strap Kit 35mm Centers
 Braided tinned copper battery strap 35 mm from center hole to center hole AND 35mm2 cross sectional area. 

These straps feature 6 mm hole width for M6 terminal bolt and are designed specifically for the Nissan Leaf 7.5 volt 2S2P battery module.

Includes strap, two M6 stainless hex head cap screws and two M6 Nord-Lock Zinc Flake washers.
Price: $9.00
Add to cart
Braided Battery Strap Kit 40mm Centers
 Braided copper battery strap 41 mm from center hole to center hole.  

These straps feature 6 mm hole width for M6 terminal bolt and can be used on smaller CALB cells such as CA60FI.

Includes strap, two stainless hex head cap screws and two Nord-Lock Zinc Flake washers.
Price: $9.00
Add to cart
Braided Battery Strap Kit 50mm Centers
 Braided copper battery strap 51 mm on center.  Kit includes strap, two hex head M6 capscrews, and two Nord-Lock zink flake wedgelock washers.

This strap can be used to connect CA60FI cells side by side.
Price: $9.00
Add to cart

« Previous | 1 | 2 | 3 | 4 | 5 | »